The Fundamentals of Plumbing Skills for Bathtub Installation
The Fundamentals of Plumbing Skills for Bathtub Installation
Blog Article
How do you actually feel when it comes to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely rocket science, yet it does call for solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a moderately difficult project. If the old tub is easily accessible, the project can relocate immediately; if you have to open up a wall to eliminate the old tub and also position the brand-new bath tub, the task is much harder. In either case, the task is within a residence handyman's skills, although you will need an assistant to leave the old bathtub and set in the new one. Make sure you have actually qualified on your own for the task as well as are comfortable attempting it. Instead of working with a service provider to take over a halfway-completed job, it is much better to consider employing one before you start. Chances are you may need a specialist plumber to make tube links.
This article will assist you install a new bath tub in your restroom if you have actually currently bought a new tub and don't need to alter the arrangement of your previous water pipes.
Your devices as well as product list must comprise the following:
Getting ready for the Installment
Firstly, the sustaining structure supplied with the bathroom ought to be fitted (if required) according to the producer's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the flexible tap adapters to the bottom of the two taps using 2 nuts and also olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its last position.
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you need to do is separate the supply of water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite problematic as a result of the restricted access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from turning during this procedure. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Before proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, put the tub in the required setting. The wooden boards are handy in evenly spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four little factors.
The next goal is to make sure that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the bath tub until the spirit level reads degree.
To mount taps, fit all-time low of the furthest flexible tap connector to the proper supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water as well as inspect all joints as well as new pipework for leakages and also tighten them if needed. Load the tub and additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, take care of the bath paneling as explained in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait up until the bath tub has been used at the very least when as this will resolve it into its final setting.
Fitting New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need lowering couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is securely in position, the supply pipes can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The previous type must be connected to the tap ends first, tightening just by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to break a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, leading to complications with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your components and also fittings. They are sold in tubes and also cartridges, and can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with spins of soaked newspaper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack fairly very early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally easily available on the marketplace. It is recommended to fit the tiles making use of waterproof or water resistant glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Do you appreciate reading about Tools You Need to Install a New Bathtub ? Make a short review down below. We would be interested to listen to your insights about this blog post. We hope that you visit us again in the future. Do you know about anybody else who is truly interested in the subject? Be sure share it. We treasure reading our article about How to Install a Bathtub Yourself.
Immediate plumbing assistance for emergencies. Report this page